Do you know your commander Bolts - Jeep Commander Forums: Jeep Commander Forum
General Commander Discussion General Discussion involving the Jeep Commander goes here. If it does not fit into a more specific category below, post it here.

 
LinkBack Thread Tools Display Modes
post #1 of 8 (permalink) Old 02-13-2011, 07:18 AM Thread Starter
Senior Member
Points: 12,698, Level: 73 Points: 12,698, Level: 73 Points: 12,698, Level: 73
Level up: 62% Level up: 62% Level up: 62%
Activity: 0% Activity: 0% Activity: 0%
 
indymtb's Avatar
 
Join Date: May 2010
Location: Fishers, IN
Posts: 362
Do you know your commander Bolts

I am taking off my pfe cai and putting the stock back in. I have everything done except that there is one bolt that fastens the intake to the engine block (I think). It is just to the left of the throttle body. Does anyone know the dimensions of that bolt? I lost it when I swapped it out originally.

Thanks in advance!

IndyMTB
---------------------------------
2010 Jeep Commander Limited/QDII,RC 2" Lift 255/70/17 Goodyear Wrangler Adventure AT
JBA UCAs, Bilstein front, Sensa-Trac F-150 rear
indymtb is offline  
Sponsored Links
Advertisement
 
post #2 of 8 (permalink) Old 02-13-2011, 08:57 AM
Moderator
Points: 10,821, Level: 68 Points: 10,821, Level: 68 Points: 10,821, Level: 68
Level up: 93% Level up: 93% Level up: 93%
Activity: 0% Activity: 0% Activity: 0%
 
SAL-XK's Avatar
 
Join Date: Apr 2010
Location: North Carolina
Posts: 1,993
Which engine do you have?


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Stop by and like the page

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
SAL-XK is offline  
post #3 of 8 (permalink) Old 02-13-2011, 09:45 AM Thread Starter
Senior Member
Points: 12,698, Level: 73 Points: 12,698, Level: 73 Points: 12,698, Level: 73
Level up: 62% Level up: 62% Level up: 62%
Activity: 0% Activity: 0% Activity: 0%
 
indymtb's Avatar
 
Join Date: May 2010
Location: Fishers, IN
Posts: 362
Sorry. Duh. Its the hemi 5.7 on a 2010 which I am guessing hasn't changed much over the years.

IndyMTB
---------------------------------
2010 Jeep Commander Limited/QDII,RC 2" Lift 255/70/17 Goodyear Wrangler Adventure AT
JBA UCAs, Bilstein front, Sensa-Trac F-150 rear
indymtb is offline  
 
post #4 of 8 (permalink) Old 02-13-2011, 02:13 PM
Moderator
Points: 10,821, Level: 68 Points: 10,821, Level: 68 Points: 10,821, Level: 68
Level up: 93% Level up: 93% Level up: 93%
Activity: 0% Activity: 0% Activity: 0%
 
SAL-XK's Avatar
 
Join Date: Apr 2010
Location: North Carolina
Posts: 1,993
I have the 4.7 and don't have that bolt your talking about I can look it up and see if I find it I'll post it if I never return I didn't find it


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Stop by and like the page

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
SAL-XK is offline  
post #5 of 8 (permalink) Old 02-13-2011, 02:19 PM
Moderator
Points: 10,821, Level: 68 Points: 10,821, Level: 68 Points: 10,821, Level: 68
Level up: 93% Level up: 93% Level up: 93%
Activity: 0% Activity: 0% Activity: 0%
 
SAL-XK's Avatar
 
Join Date: Apr 2010
Location: North Carolina
Posts: 1,993
I looked it up in the SM and didn't see any bolt to the engine while taking apart the intake system.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Stop by and like the page

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
SAL-XK is offline  
post #6 of 8 (permalink) Old 02-13-2011, 02:20 PM Thread Starter
Senior Member
Points: 12,698, Level: 73 Points: 12,698, Level: 73 Points: 12,698, Level: 73
Level up: 62% Level up: 62% Level up: 62%
Activity: 0% Activity: 0% Activity: 0%
 
indymtb's Avatar
 
Join Date: May 2010
Location: Fishers, IN
Posts: 362
Awesome. I am going to measure and grab a couple sizes. I was looking for other bolts that looked similar so I could test but didn't see any readily available. Thanks for taking the time.

IndyMTB
---------------------------------
2010 Jeep Commander Limited/QDII,RC 2" Lift 255/70/17 Goodyear Wrangler Adventure AT
JBA UCAs, Bilstein front, Sensa-Trac F-150 rear
indymtb is offline  
post #7 of 8 (permalink) Old 02-13-2011, 04:25 PM
Moderator
Points: 10,821, Level: 68 Points: 10,821, Level: 68 Points: 10,821, Level: 68
Level up: 93% Level up: 93% Level up: 93%
Activity: 0% Activity: 0% Activity: 0%
 
SAL-XK's Avatar
 
Join Date: Apr 2010
Location: North Carolina
Posts: 1,993
I just picked up a 304 piece grade 5 nut and bold kit from autozone for just $25 they also have a class 8 not grade 8 class 8 kit like 500 pieces I think for $25. Nice to have these things available as you already know now.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Stop by and like the page

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
SAL-XK is offline  
post #8 of 8 (permalink) Old 02-14-2011, 07:43 AM
Senior Member
Points: 15,906, Level: 81 Points: 15,906, Level: 81 Points: 15,906, Level: 81
Level up: 12% Level up: 12% Level up: 12%
Activity: 0% Activity: 0% Activity: 0%
 
Mongo's Avatar
 
Join Date: Oct 2010
Location: Lusby, MD
Posts: 3,037
Quote:
Originally Posted by indymtb View Post
I have everything done except that there is one bolt that fastens the intake to the engine block (I think). It is just to the left of the throttle body. Does anyone know the dimensions of that bolt? I lost it when I swapped it out originally.
Is this an intake manifold bolt? OR a bolt for a bracket to the CAI, to secure the CAI to the engine block?

Also,
Did you take the bolt off and lost it? -OR- The bolt did NOT come with the CAI kit?

If its the latter, did you check to make sure you're NOT suppose to re-use an existing bolt? Just remove a bolt already on the engine and run it through the bracket?

Your local hardware store often has a large collection of fasteners to choose from. If you do NOT know the required hardness for the bolt, then use Grade 8 for SAE or Grade 10.8 for Metric, at least. That is the standard for automotive, the last thing you want is a broken bolt on your engine.

If its an intake manifold bolt, pull one of the ones still there and take it too your hardware store, make sure to decode the markings so as to get the proper hardness. Modern engines often have some special fasteners that you are unlikely to find in the bin at the Hardware Store, and the plastic intake manifold bolts are perfect example of this, you may have to go to the dealer for the bolt.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

Last edited by Mongo; 02-14-2011 at 07:45 AM.
Mongo is offline  
Sponsored Links
Advertisement
 
Reply

  Jeep Commander Forums: Jeep Commander Forum > Jeep Commander Discussion > General Commander Discussion

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Jeep Commander Forums: Jeep Commander Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome