Code P2096 = - Jeep Commander Forums: Jeep Commander Forum
 
LinkBack Thread Tools Display Modes
post #1 of 3 (permalink) Old 07-03-2009, 06:18 PM Thread Starter
Points: 30, Level: 1 Points: 30, Level: 1 Points: 30, Level: 1
Level up: 60% Level up: 60% Level up: 60%
Activity: 0% Activity: 0% Activity: 0%
 
Join Date: Jun 2009
Posts: 1
Code P2096 =

I have COMMANDER 2008, 5,7 l, help me please
elefter is offline  
Sponsored Links
Advertisement
 
post #2 of 3 (permalink) Old 07-03-2009, 06:40 PM
Senior Member
Points: 59,678, Level: 100 Points: 59,678, Level: 100 Points: 59,678, Level: 100
Level up: 0% Level up: 0% Level up: 0%
Activity: 17% Activity: 17% Activity: 17%
 
jeep5253's Avatar
 
Join Date: Jun 2006
Location: South Carolina
Own a Commander?: Yes
Model year: 2006
Trim Package: Limited
Power-Train: 5.7L V-8 Hemi
4WD
If 4WD - system: QD-II
Current Mileage: 38,000
Posts: 14,912
Checked the code for you , could be any number of things but here is the factory pdf on that code


see below

----------------------------------------------------------------------
For a complete wiring diagram Refer to Section 8W.

When Monitored:
With the engine running in closed loop mode, the ambient/battery temperature above (-7C) 20F, altitude below 8500 ft.

Set Condition:
If the PCM multiplies short term compensation by long term adaptive as well as a purge fuel multiplier and the result is below a certain value for 30 seconds over two trips, a freeze frame is stored, the MIL illuminates and a trouble code is stored. Two Trip Fault. Three good trips to turn off the MIL.

Possible Causes
EXHAUST LEAK
ENGINE MECHANICAL PROBLEM
1/2 O2 SENSOR
(K141) O2 SENSOR 1/2 SIGNAL CIRCUIT
(K299) O2 1/2 HEATER CONTROL CIRCUIT
(K904) O2 DOWNSTREAM RETURN CIRCUIT
FUEL CONTAMINATION


Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE - DIAGNOSIS AND TESTING).

Diagnostic Test
1. ACTIVE DTC

--------------------------------------------------------------------------------

NOTE: Check the vehicle repair history. If the 1/2 O2 has been replace make sure that the O2 sensor was properly installed and meets OEM specification.



NOTE: Check for contaminants that may have damaged the O2 Sensor: contaminated fuel, unapproved silicone, oil and coolant.


Ignition on, engine not running.
With a scan tool, read DTCs.

Is the DTC active at this time?

Yes
Go To 2

No
Refer to the INTERMITTENT CONDITION Diagnostic Procedure.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)



2. EXHAUST LEAK

--------------------------------------------------------------------------------
Turn the ignition off.

WARNING: To avoid personal injury from the exhaust system being hot, allow the exhaust to cool down to a safe temperature before performing a physical inspection. Failure to follow these instructions can result in personal injury or death.


Visually and Physically inspect for holes, cracks and blockage in the exhaust system.

Is the exhaust system is good condition?

Yes
Go To 3

No
Repair or Replace as necessary.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)



3. ENGINE MECHANICAL PROBLEM

--------------------------------------------------------------------------------
Check for any of the following conditions/mechanical problems.
AIR INDUCTION SYSTEM - must be free from leaks
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leaks
ENGINE PCV SYSTEM - must flow freely
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to correct injector

Are there any engine mechanical problems?

Yes
Repair as necessary.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No
Go To 4



4. O2 SENSOR

--------------------------------------------------------------------------------



Ignition on, engine not running.
Disconnect the 1/2 O2 Sensor harness connector.
With the scan tool, monitor the 1/2 O2 Sensor voltage.
The O2 Sensor voltage should read 5.0 volts on the scan tool with the connector disconnected.
Using a jumper wire, jump the (K141) O2 Sensor 1/2 Signal circuit to the (K904) O2 Downstream Return circuit in the O2 Sensor harness connector.

NOTE: The voltage should drop from 5.0 volts to 2.5 volts with the jumper wire in place.



Did the O2 Sensor volts change from 5.0 volts to 2.5 volts?

Yes
Replace the O2 Sensor
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No
Go To 5



5. (K141) O2 SENSOR 1/2 SIGNAL CIRCUIT

--------------------------------------------------------------------------------






Remove the jump wire.
Ignition on, engine not running.
With the scan tool, monitor the 1/2 O2 Sensor voltage.

Is the voltage above 4.8 volts?

Yes
Go To 6

No
Check the (K141) O2 Sensor 1/2 Signal circuit for an open or short to voltage. Inspect the O2 Sensor connector and the PCM harness connector. If OK, replace and program the Powertrain Control Module per Service Information.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)



6. (K299) O2 SENSOR 1/2 HEATER CONTROL CIRCUIT

--------------------------------------------------------------------------------



Turn the ignition off.
Measure the resistance between ground and the (K299) O2 Sensor 1/2 Heater Control circuit in the O2 Sensor harness connector.

Is the resistance below 5.0 ohms?

Yes
Repair the short to ground in the (K299) O2 Sensor 1/2 Heater Control circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No
Go To 7



7. (K904) O2 DOWNSTREAM RETURN CIRCUIT

--------------------------------------------------------------------------------






Measure the voltage on the (K904) O2 Downstream Return circuit in the O2 Sensor harness connector.

Is the voltage at 2.5 volts?

Yes
Check the fuel system for contaminants.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

No
Check the (K904) O2 Downstream Return circuit for a short to ground, open, or short to voltage. Inspect the O2 Sensor connector and the PCM harness connector. If OK, replace and program the Powertrain Control Module per Service Information.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)

2006 Steel Blue 5.7L HEMI Limited 4x4 Build Date: June 9, 2006 Hour 14
Interior: Dark Slate/Light Graystone with Saddle Brown Leather Seats
Quadra-Drive II, NAV, DVD, Trailer Tow Group IV, Off-Road Group II, Remote Start, UConnect, Rear Backup Camera, Chrome Wheels,
Magnaflow cat-back exhaust, Daytime Running Lights enabled, 2" Rough Country Lift with 265/70R17 Goodyear Wrangler AT/S
jeep5253 is offline  
post #3 of 3 (permalink) Old 07-03-2009, 07:11 PM
Senior Member
Points: 63,765, Level: 100 Points: 63,765, Level: 100 Points: 63,765, Level: 100
Level up: 0% Level up: 0% Level up: 0%
Activity: 0% Activity: 0% Activity: 0%
 
a49erFan's Avatar
 
Join Date: Jan 2007
Location: Sunny Arizona
Posts: 12,579
Send a message via Yahoo to a49erFan
Read this thread too:

https://www.jeepcommander.com/forums/...ighlight=p2096





To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


2006 XK, Steel Armadillo Front Bumper w/Warn Powermate winch, Rear Bumper w/tire carrier & Super Sliders, Rhino Rack Roof Rack and Foxwing Awning, KC Lights on Steel Armadillo Light Bar, 4xGuard Rear Differential Cover, Steel Armadillo Plates.
a49erFan is offline  
Sponsored Links
Advertisement
 
Reply

  Jeep Commander Forums: Jeep Commander Forum > Jeep Commander Discussion > Regular Service / Maintenance > Diagnostic Trouble Codes (DTC)

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Jeep Commander Forums: Jeep Commander Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in











Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome