Jeep Commander Forum banner

1 - 1 of 1 Posts

·
Registered
Joined
·
521 Posts
Discussion Starter #1
I know everyone has been asking me for wiring for some time so here you go: Remote starts, nav installs and more! For 2006 Model

12volts lt. blue/red (20A) + ignition harness
Starter pink/orange + ignition harness
Second Starter purple/brown - ignition harness
Notes: The second starter wire is negative trigger thru a 150 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information.
Ignition pink/lt. green + ignition harness
Second Ignition N/A
Third Ignition N/A
Accessory same as second starter wire
Notes: The accessory wire is negative trigger thru a 560 ohm resistor. MUST use a relay. Refer to DirectFax document 1084 for wiring information.
Second Accessory N/A
Keysense same as second starter wire
Notes: The key sense wire is negative trigger thru an 8500 ohm resistor. MUST use a relay.
Power Lock purple/dk. green - driver door module in door
Notes: Lock is negative trigger thru a 330 ohm resistor. Unlock is negative trigger thru a 100 ohm resistor. MUST use relays.

Can also use the trigger wires for the door lock relays found at the instrument cluster, conn. 2. Lock is lt. green/dk. green in pin 5. Driver door unlock is tan/lt. green in pin 6. Passenger door unlock is purple/lt. green in pin 7.
Power Unlock same as power lock wire
Lock Motor lt. green/lt. blue 5wi plug above fuses, pin 36
Unlock Motor lt. green/dk. green 5wi plug above fuses, pin 35
Parking Lights+ do not use, relay rests at gnd
Parking Lights- (CAN data bus) (use hazards)
Hazards white/dk. blue to white/tan - SCM, 16 pin plug, pin 16
Notes: The SCM (Steering Column Module) is in the steering column.
Turn Signal(L) use hazards wire
Turn Signal(R) use hazards wire
Reverse Light white/lt. green + IPM , conn. 2, pin 2
Notes: The IPM (Integrated Power Module) is on the driver fender, behind the battery.
Door Trigger see notes - each kick or cluster, conn. 3
Notes: The LF door is purple in pin 6. The RF door is purple/white in pin 7. The LR door is purple/gray in pin 4. The RR door is purple/yellow in pin 5. Use all four wires and diode isolate each wire from each other and the control module. Refer to DirectFax 1076 for wiring information.


Dome Supervision yellow/orange - any light or cluster, conn 2, pin 12
Trunk/Hatch Pin pur/org and pur/brn (glass) - DKP or cluster, conn. 3, pins 3, 2
Hood Pin purple/lt. blue (export only) - pin sw. or FCM, 24 pin plug, pin 23
Notes: The FCM (Front Control Module) is on the driver fender, behind the battery.
Trunk/Hatch Release orange/purple - DKP or cluster, conn. 3, pin 8
Notes: Meter this wire while opening the rear glass from the switch on the rear hatch.

The hatch release motor wire is orange/gray (5wi) at the plug above the fuses, pin 25.
Power Sliding Door N/A
Factory Alarm Arm arms on lock with door open
Factory Alarm Disarm factory remote only
Disarm No Unlock with ign, keysense, Sentry Key
Tachometer NOT red/tan or dk. grn/lt. grn ac any ignition coil or fuel injector
Wait to start N/A
Brake Wire white/tan + brake pedal switch
Parking Brake dk. green/white - switch or cluster, conn. 1, pin 16
Horn Trigger dk. green/orange + horn or IPM, conn. 2, pin 35
Notes: The IPM (Integrated Power Module) is on the driver fender, behind the battery.
Memory Seat 1 lt. green/orange - driver door module in door
Notes: The memory seats are negative trigger thru resistors. The resistor values are not known at this time. Cut the wire and meter it while pressing the memory seat buttons.
Memory Seat 2 same as memory seat 1 wire -
Memory Seat 3 N/A -
Interface Module: Category:
Combo Interface Required:
No Type:
Data Bus
Part #: XK532
Alternate Part1 #: IOM-Chrysler-7
Notes: When using the combo module it is not necessary to use doc 1084. That part takes care of 2nd starter and accessory, locks, and bypass.
Interface Module: Category:
Immobilizer Bypass Required:
Yes Type:
Sentry Key
Part #: PKU-CH2X
Alternate Part1 #: 556CW
Alternate Part2 #: 556UW
Alternate Part3 #: DesignTech 20402
Alternate Part4 #: DesignTech 29402
Notes: Standard on all models.
Interface Module: Category:
Door Lock Interface Required:
No Type:
Data Bus
Part #: XK03
Alternate Part1 #: 456LW
Notes:
Smart Starter Kill Relays: Not Available




This wiring information is being provided free of charge on an "as is" basis, without any representation or warranty. It is your responsibility to verify any circuit before interfacing with it using a digital multimeter.
 
1 - 1 of 1 Posts
Top